Reactivity Monitoring of Accelerator-Driven Nuclear Reactor Systems

Research output: ThesisDoctoral thesis

Institutes & Expert groups

  • TUD - Delft University of Technology

Documents & links

Documents

Abstract

This thesis provides a methodology and set-up of a reactivity monitoring too lfor Accelerator-Driven Systems (ADS). The reactivity monitoring tool should guarantee the operation of an ADS at a safe margin from criticality. Robustness is assured in different aspects of the monitoring tool: the choice of the measurement techniques, the evaluation methods to derive the reactivity from experimental data, and the detector type and positioning.In the first chapter of the work, the experience from previous research programmes (mainly MUSE and YALINA) is used to select appropriate experimental techniques for reactivity monitoring. A combination of three techniques is assessed to monitor reactivity: The Pulsed Neutron Source (PNS) technique (with the Integrated Source Jerk (ISJ) method as alternative) for start-up (until 1 % of nominal power) and the Current-to-Flux (CTF) combined with the Source Jerk(SJ) technique during ADS operation.Static evaluation methods are used to derive the reactivity from the experimental value: the area method for start-up, the static CTF method during operation,and the static SJ method for the interim cross-checking of the ADS reactivity.These are more robust than dynamic evaluation techniques, as they do not depend on the knowledge of kinetic parameters. In the second chapter of this thesis,the spatial correction factors (SCFs) are defined that need to be applied on the reactivity values obtained by point kinetics. Via modal analysis, the SCFs are derived analytically for the selected evaluation methods.Extensions are made to the existing DALTON diffusion code in order to perform modal analysis and time-dependent experiment simulations. In this way modal analysis helps to understand the behaviour of the simulated SCFs of the complete subcritical core.In the third chapter the proposed reactivity monitoring methods are tested on the zero-power VENUS-F ADS. Thanks to the modular core, VENUS-F can operate in both critical and subcritical mode. The experimental reactivity results can therefore be compared to a value obtained by an alternative methodology, starting from a critical core. The experimental results confirm the modal analysis and experiment simulations. Finally, reactivity monitoring during operation in the MYRRHA ADS is studied in order to take into account the full-power aspects of reactivity monitoring. For the start-up reactivity monitoring and interim reactivity cross-checking MYRRHA behaves similar to VENUS concerning the SCFs for the evaluation methods. The(outer) reflector is therefore the recommended detector zone, preferably using threshold fission chambers as instrumentation.For the simulation of reactivity monitoring during operation, MCNP is usedas appropriate simulation tool to deal with the MYRRHA core in homogeneities.The relative CTF monitor is evaluated between three stages of operation: the temperature feedback during core start-up (from 1 % nominal power on), the core enlargement during the first MYRRHA cores, and the burn-up during the MYRRHA equilibrium core.Again, the MYRRHA outer reflector turns out to be a suitable detector location for reactivity monitoring also during operation, independent of the detector type. A safe (under)estimation of the absolute reactivity decrease is obtained for all stages of operation, except for the temperature feedback case. For practical reasons, only a limited number o fdetectors will be installed in the reflector. Therefore, a conservative boundary value of 500 pcm could be appropriate to take into account the locations with extreme SCFs, in case no re-calibration of the relative CTF monitor via the SJ method is possible.As a conclusion, it is possible to measure the reactivity in an ADS by combining different experimental techniques. The accuracy of the reactivity monitor will depend on the safety function it has to fulfill and the related licensing requirements.If it is possible to perform short (in the order of hundreds of µs) reproducible accelerator beam interruptions with a stable beam restoration, the absolute reactivity during operation can be determined via the SJ cross checking technique.In that case, the accuracy of the reactivity monitoring tool can be improved. The higher the accuracy, the higher the operational keff level, which is beneficial for the operational cost of an ADS.

Details

Original languageEnglish
Awarding Institution
  • TUD - Delft University of Technology
Supervisors/Advisors
  • Van den Eynde, Gert, SCK CEN Mentor
  • van der Hagen, Tim, Supervisor, External person
  • Lathouwers, Danny, Advisor, External person
  • Kloosterman, Jan-Leen, Advisor, External person
Award date4 Jan 2016
Print ISBNs978-94-6295-440-3
Publication statusPublished - 4 Jan 2016

Keywords

  • Reactivity, monitoring, Accelerator-Driven Systems (ADS), MYRRHA

ID: 947255